Acer Q276HL Manual de usuario

User GuideAcer LCD Monitor

EN-1UNPACKINGPlease check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or tra

EN-2ATTACHING / REMOVING THE BASESCREEN POSITION ADJUSTMENTIn order to optimize the best viewing position, you can adjust the tilt of the monitor by u

EN-3CONNECTING THE POWER CORDz Check first to make sure that the power cord you use is the correct type required for your area.z This monitor has a un

EN-4POWER SAVINGThe monitor will be driven into Power Saving” mode by the control signal from the display controller, as indicated by the amber-color

EN-5CONNECTOR PIN ASSIGNMENT15-Pin Color Display Signal CablePIN NO. DESCRIPTION PIN NO. DESCRIPTION1. Red 9. +5V2. Green 10. Logic Ground3. Blue 11.

EN-619-Pin Color Display Signal Cable* * only for certain modelsPIN Meaning PIN Meaning1. TMDS Data2+ 10. TMDS Cloc

EN-7STANDARD TIMING TABLEMode Resolution 1 640x480 60 Hz2 MAC 640x480 66.66 Hz3 VESA 720x400 70 Hz4 SVGA 800x600 56 Hz5 SVGA 800x600 60 Hz6 XGA 10

EN-8INSTALLATIONTo install the monitor to your host system, please follow the steps as givenbelow:Steps1.1-1Connect Video Cablea. Make sure both the m

EN-9MHLMHL (Mobile High-Definition Link) (Only for MHL-input Models) Mobile High-Definition Link is a digital interface for transmitting video and aud

EN-10USER CONTROLSPower Switch / Power LED:To turn the monitor ON or OFF.Lights up to indicate the power is turned ON.Using the Shortcut MenuPre

Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such cha

EN-11Acer eColor ManagementOperation instructionsStep 1: Press “ ” Key to open the Acer eColor Management OSD and access the scenario modesStep 2: Pre

EN-12Adjusting the OSD settingsThe OSD can be used for adjusting the settings of your LCD Monitor.Press the MENU key to open the OSD. You can use the

EN-13Adjusting the OSD position1 Press the MENU key to bring up the OSD.2 Using the directional keys, select OSD from the on screen display. Then na

EN-14Adjusting the setting1 Press the MENU key to bring up the OSD.2 Using the e/ f keys, select Setting from the OSD. Then navigate to the feature y

EN-15Product information1 Press the MENU key to bring up the OSD.2 Using the e/ f keys, select Information from the OSD. Then the basic information

EN-16(VGA Mode)TROUBLESHOOTINGBefore sending your LCD monitor for servicing, please check the trouble-shooting list below to see if you can self-diagn

EN-17(DVI/HDMI/MHL cable) ProblemsCurrent StatusRemedyLED ON·Using OSD, adjust brightness andcontrast to maximum or reset to theirdefault settings.LED

Acer I

Acer America Corporation :HVW6DQ&DUORV6W6XLWH6DQ-RVH CA 95110, U. S. A. Tel : 254-298-4000 Fax : 254-298-4147 www.a

EnglishFor any customers who own the EPEAT Gold registered models1, Acer offers the following services at your costs2:1. Additional 3 years warranty

iiiInformation for your safety and comfortSafety instructionsRead these instructions carefully. Keep this document for future reference. Follow all wa

ENERGY STAR®Acer’s ENERGY STAR qualified products save you money by reducing energy costs and helps protect the environment without sacrificing featu

ivAccessibilityBe sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possi

vampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total ratin

viNote: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage an

viiNevertheless, some pixels may occasionally misfire or appear as black or red dots. This has no effect on the recorded image and does not constitute

viiiTaking care of your visionLong viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens,

TABLE OF CONTENTSUNPACKING....................... 1ATTACHING / REMOVING THE BASE.