Acer AB460 F1 Manual de usuario Pagina 318
- Pagina / 618
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4 Networking Switch Modules
298
Syslog Mail Configuration
Clicking the MAIL tab brings up the SYSLOG MAIL CONFIGURATION page,
which allows you to configure the mail server and mail addresses for
the syslog feature. The parameters for this page are shown in the
following table.
Facility This parameter allows you to select supported facilities.
The switch supports syslog standard supported facilities
LOCAL0, LOCAL1, LOCAL2, LOCAL3, LOCAL4, LOCAL5, LOCAL6,
LOCAL7 and USER.
Traps This parameter helps you to select a particular trap
type. The following types of traps are supported
A
LERTS, CRITICIAL, DEBUGGING, EMERGENCIES, ERROR,
I
NFORMATIONAL, NOTIFICATION and WARNINGS.
Figure 4-186. Syslog Mail Configuration
Parameter Description
Mail Server IP
Address
This parameter specifies the IP address of the mail
server. Make sure the mail server is reachable.
Sender Email ID This parameter specifies the Email ID to be shown as
the From address on Syslog Emails.
Parameter Description
- AB7000 Series 1
- User Guide 1
- Safety instructions 3
- Using electrical power 4
- Product servicing 5
- Additional safety information 6
- Disposal instructions 6
- Mercury advisory 6
- Finding your comfort zone 7
- Taking care of your vision 7
- Developing good work habits 8
- FCC notice 9
- Notice for Australia 11
- Notice for New Zealand 11
- Laser compliance statement 12
- List of applicable countries 13
- Contents 15
- Index 597 20
- 1 Document 21
- Description 21
- About this Manual 22
- Manual Organization 22
- Appendix A 23
- 1 Document Description 24
- 2 Chassis 25
- Enclosure 25
- Introduction 26
- Front panel 27
- Rear Panel 28
- Blade Configuration 29
- Rear Modules 30
- Setup and Installation 31
- Rack Precautions 32
- Server Precautions 32
- Rack Mounting Considerations 33
- Rack Mounting Hardware 34
- Installing an enclosure: 35
- Chassis Management Module 38
- Reset Button 39
- Module Installation 40
- Configuring the CMM 41
- (see Figure 2-11 ) 42
- Example: 43
- • IP address: 192.168.100.101 43
- • Subnet Mask: 255.255.255.0 43
- • Default Acer: 192.168.100.1 43
- CMM Functions 44
- Local KVM 45
- Remote KVM over IP 45
- Serial Over LAN (SOL) 45
- Monitoring Functions 46
- Power Consumption Management 46
- Firmware 47
- Acer Smart Blade Console 48
- Main Menu Icons 50
- Blade System 52
- Power Supply 54
- Gigabit Switch 55
- InfiniBand Switch 57
- Drive Redirection 62
- RIVE REDIRECTION settings 63
- screen (Figure 2-23) and 64
- System Health 65
- User Management 67
- Users & Groups 68
- Permissions 70
- KVM Settings 72
- RE-CONFIGURED option above 74
- ES in the dialog boxes 74
- Keyboard/Mouse 75
- EY RELEASE 76
- IXED SCALING check box and 76
- Device Settings 77
- ONE, DHCP 78
- UTO-DETECT, HALF DUPLEX 79
- Dynamic DNS 80
- ORCE, the applet will 82
- CCESS CONTROL 83
- VENT LOG under 85
- YSTEM HEALTH 85
- Update Firmware 88
- Unit Reset 89
- Drive Redirection Screen 93
- Remote Console Options 94
- Monitor Only 95
- Exclusive Access 95
- Readability Filter 95
- Local Cursor 96
- Chat Window 96
- Video Settings 97
- Soft Keyboard 97
- Local Keyboard 98
- Encoding 99
- Power Supply Modules 100
- Power Supply Failure 101
- Installing a Power Supply 101
- Removing a Power Supply 102
- Power Supply Fans 103
- Power Components 104
- Power Cord Tie and Clamp 105
- 2 Chassis Enclosure 106
- Double-Wide Modules 107
- (for top bay) 108
- (for bottom bay) 108
- 3 Server Blades: 111
- Setup and 111
- Installation 111
- Overview 112
- Installing Blade Modules 112
- Processor Installation 115
- Installing a Processor 116
- DIMM Installation 117
- Hard Disk Drive Installation 118
- Removing a Hard Drive Carrier 119
- Installing a Hard Drive 119
- Card installation 120
- Installing via PXE Boot 122
- Installing via Virtual Media 123
- Acer Smart Console 124
- Using the Internet Browser 125
- Computer 125
- The IPMI Main Page 126
- 1 Submenu Bar (Callout #1) 127
- Server Health 128
- Figure 3-63. Server Health 129
- Refresh (#5) 130
- Show Thresholds (#6) 130
- Figure 3-65. All Sensors 131
- Event Log 132
- Figure 3-67. Event Log Status 133
- Configuration 134
- Configuration - Alerts 135
- Modifying Alerts 136
- Settings 138
- Figure 3-76. Network Settings 142
- Figure 3-77. Remote Session 143
- Configuration - SMTP Settings 144
- Figure 3-80. User Settings 146
- Figure 3-81. Main Menu 147
- Remote Console 148
- Figure 3-83. Java Started 149
- Figure 3-84. Video 149
- Figure 3-85. Keyboard 150
- Figure 3-86. Macros 151
- Figure 3-88. Soft Keyboard 153
- Remote Console - Media 154
- Virtual Media 155
- Figure 3-92. Virtual Media 156
- Remote Control-Launch SOL 157
- Figure 3-94. SOL 158
- ConfirmationWindow 158
- Figure 3-95. Baud Rate 159
- Server Power Control 161
- Figure 3-98. Power Control 162
- Maintenance 163
- Figure 3-100. Firmware 164
- Miscellaneous 165
- Language 166
- AB460 F1 167
- Power Button 168
- KVM Button 168
- KVM Connector 169
- Front Panel LED Indicators 169
- Blade Unit Components 170
- 4 DIMMs (system memory) 171
- 5 Airflow Deflector 171
- 6 CPU Heatsinks 171
- 7 Top Cover 171
- Item Description 171
- Mainboard 172
- CMOS Clear 173
- Memory Support 174
- Memory Installation 174
- Populating Memory Slots 174
- 1GB 1GB 1GB 181
- 1GB 1GB 1GB 1GB 1GB 1GB 181
- Hard Disk Drives 183
- AB460 F1 System BIOS 185
- BIOS Updates 186
- Flashing BIOS 186
- Running Setup 187
- Main BIOS Setup 188
- System Overview 189
- Advanced Settings 190
- Boot Features 191
- Power configuration 192
- Advanced Chipset Control 195
- CPU Bridge configuration 196
- NorthBridge configuration 198
- SouthBridge configuration 199
- IDE/SATA configuration 200
- •DMA Mode 202
- PCI/PnP configuration 203
- Super IO Device configuration 204
- ACPI configuration 205
- Security 206
- Server Management Settings 208
- System Information 209
- Remote Access Configuration 211
- Event Log Configuration 212
- Figure 3-126. Boot Setup 213
- Boot Device Priority 214
- Removable Drives 216
- CD/DVD Drive 217
- Network Drives 218
- Exit Options 219
- Creating a RAID Volume 221
- Initialing a RAID Volume 222
- Assigning a Hot Spare Disk 222
- AB2x280 F1 223
- LED Indicators 225
- For CPU2 231
- For CPU1 231
- Supported Memory Population 232
- Capacity 234
- CPU 1 CPU2 234
- CPU1 CPU2 236
- AB2x280 F1 Hard Disk Drives 238
- AB2x280 F1 System BIOS 239
- Figure 3-156. Boot Setup 268
- Assigning a Hot Spare Drive 277
- 4 Networking 281
- Acer 1/10Gb Ethernet Switch 282
- Installing/Removing a Switch 283
- Removing a Switch Module 284
- Configuring the Switch Module 285
- Network Connection 286
- Address Defaults 286
- OGIN screen 287
- Command Line 289
- Baudrate = 9600 290
- Data bits = 8 290
- Parity = None 290
- Stop bit = 1 290
- CX4 CX4 SFP 291
- Web-based Management Utility 294
- Nomenclature 295
- OGIN button 296
- OME page of the utility. See 296
- Home Page 297
- Top Page Links 298
- Top LED Display 299
- Left Side Tree 299
- System Management Page 300
- System Settings 301
- System Version 303
- File Management 304
- File Copy 305
- Firmware Upgrade 306
- Management Security 306
- Enable Passwords 307
- Enable Password 307
- Management User Account 308
- Authentication 309
- Accounting 309
- TACACS+ Global Settings 310
- TACACS+ Server Configuration 311
- IP Authorized Manager 312
- SSH Configuration 314
- SSL Configuration 315
- Syslog Configuration 317
- Syslog Mail Configuration 318
- MAC Based ACL 319
- IP Standard ACL 320
- IP Extended ACL 322
- WEBGUI Settings 324
- GENT CONTROL SETTINGS 325
- SNMP Community Settings 326
- Volatile Storage 327
- SNMP Group Settings 328
- SNMP Group Access Settings 329
- SNMP View Tree Settings 330
- SNMP Target Address Settings 331
- SNMP User Settings 334
- SNMP Trap Settings 335
- SNMP AgentX 336
- RMON Basic Settings 337
- Event Configuration 338
- RMON Alarm Configuration 339
- Absolute Value 340
- Incremental Value 340
- Rising Alarm 340
- Falling Alarm 340
- History Control Configuration 342
- QoS Basic Settings 343
- QoS Classmap Settings 344
- QoS Policymap Settings 345
- CoSQ Scheduling Algorithm 346
- NTP Settings 348
- Timezone Settings 349
- NTP Servers 349
- NTP Servers Keys 349
- Enabling Stacking 350
- Adding Stacking Members 351
- Removing a stacked switch 352
- • “Stack Details” on page 335 353
- Stack Configuration 354
- Stack Details 355
- Stack Counters 357
- High Capacity 358
- Layer 2 Management 359
- Port Manager 360
- Port Basic Settings 361
- Port Monitoring 362
- VLAN Traffic Class 363
- Port Control 364
- No-negotiation 365
- Rate Limiting 366
- VLAN Basic Settings 368
- Customer /Provider 369
- Port Settings 370
- Static VLAN 371
- Protocol Group 372
- Port Protocol 372
- MAC Based VLAN 373
- Unicast MAC 374
- Wildcard 375
- Switch Port VLAN 376
- Dynamic Vlan 377
- Port Configuration 378
- GARP Timers 379
- RSTP Global Settings 380
- RSTP Basic Settings 381
- Point-to-point 383
- Non-point-to-point 383
- Dynamically 383
- Port Status 384
- MSTP Basic Settings 386
- MSTP Timers 388
- VLAN Mapping 390
- CIST Port Status 392
- LA Basic Settings 394
- Interface Settings 395
- Basic Settings 398
- Authorized 400
- Un-Authorized 400
- Port Based 400
- Local AS 402
- MAC Session Info 403
- Unicast Filters 404
- Multicast Filters 405
- Layer 3 Management 407
- Vlan Interface 408
- IP V4 Interface Settings 409
- IP Route 410
- LoopBack Basic Settings 411
- IPv6 Route Configuration 412
- IPv6 Interface 413
- ND Cache 415
- Address Settings 416
- Address Profile 417
- Prefix Settings 418
- DHCP Server 419
- Pool Settings 420
- DHCP Relay 421
- RIP Basic Settings 423
- Interfaces 424
- END VERSION, but it allows 425
- Neighbors List 426
- Security Settings 427
- Address Summarization 428
- RIP6 Interface 429
- OSPF Basic Settings 431
- Interface 434
- Virtual Interface 435
- OSPF Neighbor 436
- OSPF RRD Route Configuration 437
- OSPF Area Aggregation 438
- External Aggregation 439
- Parameter Description 440
- OSPFv3 Basic Settings 441
- OSPF V3 External Aggregation 446
- – When set to 447
- BGP Basic Settings 448
- BGP Peer Configuration 450
- BGP MED Configuration 451
- Local Preference 452
- BGP Filter 454
- Route Aggregations 455
- Advanced BGP Configuration 456
- BGP Community Management 458
- RRD Basic Settings 460
- Static routes 461
- RIP routes 461
- OSPF routes 461
- Direct 462
- BGP routes 462
- RRD6 Basic Settings 464
- RRD V6 OSPF 466
- OSPFv3 routes 467
- VRRP Basic Settings 468
- VRRP Settings 468
- RIMARY IP ADDRESS for the 469
- RIORITY for the Virtual 469
- UTHENTICATION TYPE for 469
- UTHENTICATION KEY for the 469
- REEMPT MODE 469
- Multicast 470
- GMP Snooping 471
- Disabled 472
- IGMP Snooping Timer 473
- IGMP Snooping Interface 474
- IGMP Snooping VLAN Router 475
- IGMP MAC Forwarding 476
- Dynamic Multicast 477
- ESTRICTED GROUP 478
- EGISTRATION on this port 478
- Interface Configuration 480
- Group Information 481
- Source Information 482
- Component 484
- Candidate RPs 486
- Threshold 487
- Static RP 488
- DVMRP Basic Settings 490
- Statistics 492
- Interface Statistics 493
- Ethernet Statistics 494
- ADIUS SERVER ADDRESS 496
- ORT NUMBER 496
- OUND TRIP TIME in seconds 496
- TACACS+ Statistics 498
- RMON Ethernet Statistics 500
- THERNET STATISTICS page 501
- SNMP Statistics 503
- Received Statistics 506
- Current DB 507
- VLAN Port Statistics 508
- VLAN Multicast Table 509
- VLAN Counter Statistics 510
- VLAN Capabilities 511
- VLAN FDB Entries 512
- RSTP Statistics 513
- RSTP Port Statistics 514
- MSTP Statistics 516
- MSTP CIST Statistics 517
- MSTP MSTI Port Statistics 519
- Link Aggregation (LA) 520
- LA Neighbor Statistics 522
- 802.1X Session Statistics 523
- 802.1X Supplicant Statistics 524
- Mac Session Statistics 525
- ARP Cache 527
- ICMP Statistics 528
- IP V6 Interface Statistics 530
- ICMP V6 Statistics 532
- RIP Statistics 535
- RIP6 Interface Statistics 536
- RIP6 Route Information 537
- OSPF Route Information 539
- OSPF Link State DB 540
- OSPFV3 Route Information 541
- OSPFV3 Link State DB 542
- VRRP Statistics 543
- VRRP Global Statistics 544
- IGMP Snooping 545
- IGMP Snooping V3 Statistics 548
- IGMP Statistics 549
- PIM Interface Statistics 551
- PIM Neighbor Statistics 552
- PIM BSR Info 553
- PIM RP Set Information 554
- PIM Route Information 555
- DVMRP Routers 557
- DVMRP Multicast Routers 558
- DVMRP Prune Statistics 559
- Firmware Upgrading Procedures 560
- Management Utility 561
- <ip-address> 564
- <filename> 564
- InfiniBand Modules 567
- Installing the Module 568
- Removing the Module 568
- InfiniBand Switch LEDs 571
- 5 Acer Smart Blade 573
- Acer Smart Blade Manager 574
- Blade System tab 575
- Power Control 578
- Acer switch 581
- Temperature 582
- Acer Switch Configuration 582
- Setting CMM time 584
- Flash Firmware 585
- Slave CMM 586
- InfiniBand 586
- Voltage and Temperature 587
- Failure Summary 588
- Blade Summary 589
- Power Supply Summary UI 589
- Switch Summary UI 590
- Text Console 591
- KVM console 592
- Logon Management 595
- Update User Data 596
- Update Password 596
- CMM Setting 598
- Connecting to the Slave CMM 599
- 5 Acer Smart Blade Manager 600
- Appendix A: 601
- Troubleshooting 601
- BIOS POST Messages 602
- BIOS POST Codes 607
© 2020, manymanuals.es. Todos los derechos reservados | 1.326 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales